makita drill

1. Posted: Jan 4 2008

   First of all - This is only a 2.1 amp drill. I use it for pre-drilling nail holes in hardwoods and small holes in metal for screws. I generally leave a 3/32" bit or a finish nail in it when woodworking. It doesn't reverse and has only one speed bit it's SO FAST that it does a great job on small holes. A Keyless Chuck would be nice though.

2. Posted: Feb 6 2007

   overpriced, no var. speed, no reverse, and does not even have a keyless chuck!

See all reviews...

1. Posted: Nov 1 2007

   Powerhouse drill!
   This is a great drill. Very powerful for the frame size and price. The trigger is very smooth operating. Excellent value!
   

2. Posted: Nov 1 2007

   Makita drill
   These last forever! We have been using Makita drills for years and years and they keep going and going.
   

3. Posted: Oct 31 2007

   electric drill
   The drill offers unlimited torque all the time since it is AC powered. It has a side grip which keeps the tool from breaking your wrist. It also has a comfortable grip and is easy to operate. I would highly recommend this for your Makita collection.
   

See all reviews...

1. Posted: Jan 25 2007

   I was so tired of buying junky home tools from Home Depot for about the same cost I decided to take a chance on this refurbished model, and I'm glad I did. For what I could have bought a 1/4" consumer product from a big box retailer I got this heavy duty 1/2" workhorse. It's powerful, has a great "turbine"-like whir to it, and I expect it will last a very long time.

See all reviews...

1. Posted: Mar 16 2008

   This is one great drill. I was looking for a good basic drill for work in the shop,for general drilling and driving screws[witout constantly changing batteries] and this Makita more than fits the bill.Not too big,not too small. I already have a 1/2" Porter-Cable, a Porter-Cable hammer drill, a Milwaukee hole shooter, as well as a Makita cordless.However the one I reach for most is the 6402. It's just the right size, not too heavy and has good balance,and plenty of power. Say what you want about keyless chucks, they are a great convience, but give me a keyed chuck anyday. It only takes a few seconds more and a little effort.But they are the only ones that really lock the bit tight. Nothing more frustrating than to have constantly tighten up the chuck. Ive used it to drill and drive screws, and have put hole saws on it as well,and used a 1" forstner bit, and it has worked effortlessly,and it does not slip either. The reverse switch is in a good spot on the bottom,does not get in the way. No woodworker/handyman's tool box is complete without a Makita 6402. Its not the biggest,the baddest or the most powerful drill out there. But if you are looking for a great all around drill, the Makita 6402 is for you.[And the battery never seems to die just when you need it most] I almost bought a Milwaukee 3/8" drill. Its a super drill, but the size and weight are just like a 1/2" : kind of like a 1/2" drill disguised to look like a 3/8". A great drill, but I already have a 1/2", I dont need 2. Give this a workbench test drive, I doubt you will be disappointed. Ohh, did I forget to mention, its made in U.S.A.!! How many tools can you say that about today?

See all reviews...

1. Posted: Jan 4 2007

   Excellent drill. I bought this to use on an as-needed basis and ended up using it a whole lot. It is really well built and worth the little bit more that you might spend versus a competitor. Just get it... and hang shelves, adjust everything, install an A/C, build something from random Home Depot parts.. whatever. Very handy tool.

2. ( 1 of 1 found this review helpful ) Posted: Jul 10 2006

   After breaking the keyless chuck (don't ask). I too was stumped as to how to remove it. I finally decided I had nothing to lose by taking the drill apart. After clamping the broken end of the chuck in a vise, I was able to apply enough force to the gear to unscrew the shaft from the chuck. A new replacement chuck screws back on the same way. This is a great drill and I'm very pleased with it's performance.

3. ( 8 of 8 found this review helpful ) Posted: Jun 21 2005

   This drill packs alot of power for only 4.9 amps. The tool is very well balanced and very quiet. I would have given it 5 stars if not for the "unremoveable" chuck. The owners manual does not give any instructions on how to remove nor is there any discernable fiting inside the chuck. All in all a good drill with ample power. Remember Makita makes their own motors.

See all reviews...

1. Posted: Dec 12 2007

   I've been using this drill for a few weeks and my only regret is that I waited so long to buy one. This was purchased to replace another angle drill I had been using (yellow and black) that didn't perform to my expectations, when it finally died I went with the Makita. It's not the least expensive, but I've always had good experiences with Makita products in the past, so the choice was easy. I've been boring holes in treated lumber, studs, joists, glue lam beams, ect.. with a self feeding bits, and this drill powers through with no problems. Only downfall is the Allen key holder that is built into the grab handle, the wrench tends to fall out sometimes, this didn't keep me from giving it 5 stars, I just leave the key in the case.

2. Posted: Jan 25 2007

   amazon was great,great price and quick shipping...the drill is wonderful.having owned and used the hole hawg in the past,this ones better.im a plumbtrician so i need to drill holes from a half inch to five and a half inch diameter on a daily basis.i use my inch and an eight 18" naileater and even in southern yellow pine it hardly bogs the drill down.use sharp bits and be sure to read the directions for bracing the drill.it will hurt you quickly.....

3. ( 0 of 1 found this review helpful ) Posted: Jan 23 2007

   based on price ...performance....features...this tool is a best buy in the category of commercial quality plumbing-electrical specialty drills

See all reviews...

1. ( 4 of 4 found this review helpful ) Posted: Sep 19 2005

   If you've never used this type of drill, be forewarned: This tool has so much torque, especially at the 300-RPM setting, that you could be hurt if not careful. This isn't a tool for a woman, unless she's a weightlifter. For large holes, at least 3" and up, you must absolutely use the side handle. This is because when a large bit becomes stuck while you're drilling, a common scenario, the tool itself starts to rotate - so you need to be holding on with every ounce of strength you have to prevent that - and be quick to release the switch. If you don't, it could lift you right of the ground, twist your arms like pretzels, or mash your fingers, etc. Think safety, and you'll be fine. The off/on switch is a spring-loaded rocker. For safety reasons, it can't be locked in the "on" position. To turn the bit clockwise, squeeze the rear of rocker-switch. To go counter-clockwise, squeeze the front of the switch. Release the switch, and it instantly moves to the middle/off position - and the bit will stop quickly. To change speeds, pull out a pin on a control near the front handle, and move the slide to the other speed. Both switches are perfect. This tool is uncannily similar to the Milwaukee 1676.6 half inch Hole-Hawg kit (the specs are nearly identical). If the handles were the same color, you'd have to look real close to see which is which. The same goes for performance - they feel pretty much the same in use, and both are outstanding. However, there are two notable differences: 1.

2. ( 4 of 4 found this review helpful ) Posted: Sep 19 2005

   Makita DA6300 Heavy Duty [compact] Right-Angle Drill If you've never used this type of drill, be forewarned: This tool has so much torque, especially at the 300-RPM setting, that you could be hurt if not careful. This isn't a tool for a woman, unless she's a weightlifter. For large holes, say 3" and up, you must absolutely use the side handle. This is because when a large bit becomes stuck while you're drilling, a common scenario, the tool itself starts to rotate - so you need to be holding on with every ounce of strength you have to prevent that - and be quick to release the switch. If you don't, it could lift you right of the ground, twist your arms like pretzels, or mash your fingers, etc. This phenomenon is call kickback. Think safety, and you'll be fine. The off/on switch is a spring-loaded rocker. For safety reasons, it can't be locked in the "on" position. To turn the bit clockwise, squeeze the rear of rocker-switch. To go counter-clockwise, squeeze the front of the switch. Release the switch, and it instantly moves to the middle/off position - and the bit will stop quickly. To change speeds, pull out a pin on a control near the front handle, and move the slide to the other speed. Both switches are perfect. The DA6300 comes with a steel case (part no. 181685-2), but it's flimsy, has a lousy handle and latches, and has sharp non-rolled edges. The case has four protruding dimples designed as "feet". However, the case half edges poke out beyond the "feet", so don't set the case's feet on a hardwood floor, counter-top, etc., as it could scratch the surface. The case's steel is only .033" thick. Makita should be embarrassed to put their name on it, which is probably why they don't have a photo of it on their web site. Click "see customer images" above for photos of my case. The 5 stars are for the drill. The case deserves zero stars. September 2007 update: When I purchased this tool, I needed a compact heavy-duty right angle drill, such as this one or the Milwaukee Hole Hawg. Neither one had, or even has now, a clutch to prevent tool damage and operator injury during serious kickback. Recently, Ridgid introduced this type of drill, the Model R7130, which has this important safety feature. After using the DA6300 for a dozen years, my drill bit the dust. I failed to let the drill come to a complete stop before moving the speed selector. (The user guide didn't say the drill had to be stopped to change speeds.) Grinding noises started immediately and the drill chuck stopped moving. Several gears were stripped and the aluminum case cracked. Tool was a total loss. Don't make the same mistake.

See all reviews...